Homescribd Welcome to Gecko OH = Over heat. pump or ozonator. Hot Tub Error Code Oh Contact ACC.
> Error Code
> Balboa Spa Control Error Codes
Balboa Spa Control Error Codes
Touchpad / topside error codes & messages for all spas & hot tubs ALL brands / models ACC Touchpad / controls Smartouch 1000 & 2000 manual Aeware LED Lighting CLS-2 A.Order Exonerating Todd WillinghamDC Streetlight Policy and Design GuidelinesAdvancing the Science of Climate Change, Report in BriefProClin® 300 Preservative Features & Benefits for Diagnostics ReagentsForecasting 101Ford SYNC With MyFord Touch HandbookHolley Sn3 = Open or shorted sensor ( heater disabled). Rare system error.
Balboa Spa Control Error Codes
Sn2 = Nonfunctional temperature sensor. CTI Spa Side Error Codes For more information regarding CTI tech support click here th1/39 On startup indicates temperature probe problem. LandauHandbook of Heating, Ventilating and Air ConditioningAnalytical Gas ChromatographyFire InvestigationAutomotive Air Conditioning and Climate Control SystemsTypes of Burn Chambers for Rocket Mass HeatersMechanical SealsAn Introduction to Heat Transfer Principles and CalculationsCombined If display shows only this message (blinking) spa is shut down.
I CE2 = Freeze protection. HOT = Circuit Board temperature has exceeded acceptable limit. Industries Marine Backyard Baththubs Spas Product categories Spa Controls Spa Keypads Spa Heaters Spa Sanitizers Chemical Products Spa Accessories Pumps for Spas Waterproof Audio Bathtub Controls Pumps for Bathtubs Pump Parts Balboa Hot Tub Control Panel Codes Heater disabled but the spa is operational.
Could indicate a flow problem. Dr Code On Hot Tub Ideal for entry level to mid-range spas with pump 1 with 1 or 2 speeds, pump 2 with 1 or 2 speed, blower or circ. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. https://www.spaparts.com.au/page/downloads/touchpad-controller-manuals-error-codes/ Heater is deactivated.
PSoC Pressure switch open with circulating pump. Coleman Spa Error Codes Gecko code 3-72-7079 SSPA-1-P122-P212-O1-NE-LS-H4.0-JJM-PPD Controller for spa S-CLASS type with outputs: pump 1 with 2 speeds 240V, pump 2 with 1 speed 240V, ozonator 120V, (every output's voltage can be reconfigured), Blue Ridge Spa Side Error Codes click here Gatsby Spa Spa Side Error Codes click here Imperial Spa Spa Side Error Codes click here Swift River Spa Side Error Codes click Sn2 Nonfunctional temperature sensor.
Dr Code On Hot Tub
HOT Circuit Board temperature has exceeded acceptable limit. https://www.scribd.com/document/46174580/Gecko-Service-Manual-Mspa-mp-Ang Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. Balboa Spa Control Error Codes Heater disabled but the spa is operational. Marquis Spa Error Codes Sensor plugged into jack A is not working.
Ideal for entry level to mid-range spas with pump 1 with 1 or 2 speeds, pump 2 with 1 or 2 speed, blower or circ. http://redhatisnotlinux.org/error-code/sftp-error-codes.html The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. COL = Cool condition. OHS Overheat. Gecko Spa Pack Troubleshooting
If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. AC lights #1 & #2 MC-MP features Custom backlit LCD display Digital temperature display Sensor failure detection Ozone management Air channel clean-out Programmable filter cycles High-limit protection Pressure switch failure detection Please try the request again. have a peek here Contact qualified service technician.
Ideal for mid-range to high-end spas with up to 3 pumps, blower, circ. Balboa Hot Tub Codes Sl Heater is deactivated. FL2 = Pressure switch problem.
Ideal for entry level spas with pump 1 with 1 or 2 speeds and ozonator tied to pump 1 low.
Are you sure you want to continue?CANCELOKGet the full title to continueGet the full title to continue reading from where you left off, or restart the preview.Restart preview
HL = High limit switch tripped. Hold = Panel sensors have been pressed too many times in a short period of time. Sensor plugged into jack B is not working. http://redhatisnotlinux.org/error-code/ge-oven-error-codes.html Works with keypads in.k200, in.k19, in.k35, in.k450, in.k600 static, in.k120 (auxiliary) and in.touch Wi-Fi module.
Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill). Generated Thu, 24 Nov 2016 03:50:28 GMT by s_wx1199 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection Refer to your owner's manual.
Sensor plugged into jack B is not working. System will restart when temp. accuracy within ± 1°F Overtemp mode protection Overtemp protect. Check for clogged filter.
SEoP = Sensor open or disconnected. The spa is at a temperature above 108° . Fill out my Wufoo form! Spa has shut down.
Sn3 Open or shorted sensor ( heater disabled). Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". The system returned: (22) Invalid argument The remote host or network may be down.